Error codes · Samsung
Samsung Refrigerator Error Codes
A Samsung refrigerator shows a code when its control board sees something it does not like: a fan that is not turning, a sensor reading out of range, a voltage problem or an ice maker that is not finishing its cycle. Here is what the common codes mean, what you can safely try, and when it is time for a technician.
- 18codes explained
- Checkedagainst Samsung sources
- From $59if you need us
How to read Samsung refrigerator codes
Most Samsung refrigerators show a number followed by E (an error) or C (a check). The same number usually points to the same area: 22E and 22C both relate to the refrigerator fan, for example. Family Hub models can list current and past codes under Fridge Manager, Fridge Settings, Self Check. Samsung itself asks owners not to unplug the refrigerator or press panel buttons to clear a code unless a step says to, because that wipes information a technician uses.
Code list
Fans and airflow
Freezer fan error. The board does not see the freezer fan turning, often because it is frozen in ice after a door was left open or a gasket gap let moist air in, or because the motor has failed.
What to do: Make sure doors close fully and nothing blocks them. If the fan is iced, a full defrost may free it. If the code returns, the fan or a defrost part needs service.
Refrigerator fan error, often after a door was open for a long time.
What to do: Unplug, leave the doors open for a few hours to melt ice, then plug back in and close the doors. If it comes back, call for service.
Ice room fan error.
What to do: Usually ice around the ice compartment fan. Needs a defrost and a look at why ice formed.
Sensors and defrost
Refrigerator defrost sensor error.
What to do: Points to the defrost sensor or its wiring. A technician tests the sensor and the defrost circuit.
Ice maker (freezer side) sensor error.
What to do: Sensor or wiring in the ice maker area. Service needed.
Ice maker sensor error.
What to do: Sensor or wiring in the ice maker area. Service needed.
Ice pipe heater error.
What to do: The heater that keeps the ice chute or fill area from freezing is not working right. Service needed.
Ice maker function error.
What to do: The ice maker is not finishing its cycle: frozen fill tube, water supply or the ice maker module. Check that water is on; then call.
Compressor and power
Abnormal compressor current, possibly after a power surge.
What to do: Turn off the breaker or unplug for 60 seconds, then restore power. If it returns, call for service.
Compressor lock.
What to do: The compressor is not starting. This needs a technician with meters.
Compressor under-voltage, often after a brownout.
What to do: Power off for 60 seconds, then restore. Repeated codes mean checking the outlet and circuit as well as the refrigerator.
Compressor over-voltage, often after a surge or storm.
What to do: Power off for 60 seconds, then restore. If it returns, call.
Communication fault, can happen if power dropped while the refrigerator was starting up.
What to do: Power off for 60 seconds, then restore.
Communication error between boards, sometimes after a surge or when a door wire harness is not connected.
What to do: With power off, check that the harness above the door is connected, then restore power. If it returns, call.
Not a fault
Cooling Off (demo or shop) mode. The lights work but nothing cools.
What to do: Turn it off per the manual; on many models you hold the top two buttons on the left panel for about 5 to 8 seconds until it chimes.
Normal self-check after a power cut.
What to do: Wait for it to finish.
Ice bucket not seated.
What to do: Remove and reseat the bucket.
Wi-Fi setup access point.
What to do: Clears when setup finishes.
Before you call
What you can safely try
- Check that every door closes fully and nothing on a shelf blocks it.
- Look at the gaskets for gaps or tears.
- For power codes (83E, 85E, 86E, 88 88), power off for 60 seconds and restore.
- For fan codes after a door was left open, a full defrost with doors open can clear ice.
- Write the code down before you do anything else.
Turn off power before you touch anything inside the refrigerator. If a step needs tools or panels removed, leave it to a technician.
When to call
When it is time for a technician
- The same code returns within days.
- Temperatures are rising and food is at risk.
- You hear clicking from the back and the compressor does not run.
- Ice keeps building up around fans or the ice maker after a defrost.
A code tells you where to look, not which part failed. We confirm the cause with tests and readings before we quote. Diagnostic from $59, credited toward the repair. Refrigerator repair · Samsung repair
Denver note
What we see in the Denver area
Summer storms along the Front Range bring power blips and surges. Codes 83E, 85E and 86E after a thunderstorm are common, and a 60-second power cycle often clears them. If they come back regularly, have the circuit checked too.
Sources
Where this information comes from
Code meanings are checked against Samsung's own published support material and written here in plain language. Models differ, so your owner's manual has the final word.
Pricing
What it costs to get started
One diagnostic fee, credited toward the repair. The full price in writing before any work starts.
Repair prices depend on the part and the labor, so we quote after the diagnosis instead of guessing on the phone. If a repair is not worth it, we will tell you.
Diagnostic visit
from $59
Credited toward the repair
FAQ
Questions we hear
Call (719) 745-8080 with anything not covered here.
Can I just reset a Samsung refrigerator code?
For power and communication codes, a 60-second power cycle is what Samsung recommends. For fan, sensor and ice maker codes, a reset only hides the problem, and it can erase information a technician uses.
Why does my Samsung keep showing 22E?
Usually ice on the refrigerator fan. A door left open or a poor gasket lets moist air in. Defrosting clears it for a while, but if the cause is a defrost part or a gasket, it comes back.
Related