Skip to content
(719) 745-8080

Error codes · Whirlpool

Whirlpool Washer Error Codes

Whirlpool washers use two kinds of codes: short words like LF, Sud or OL that tell you about the load or the hookup, and F-E codes like F5 E2 or F9 E1 that point to a system. Many have a simple fix. Here is the list for top-load and front-load models.

  • 18codes explained
  • Checkedagainst Whirlpool sources
  • From $59if you need us

How to read Whirlpool washer codes

An F-E code reads as a group and a detail: F8 E1, for example, is a water fill problem. Whirlpool's usual way to clear an F-E code on front-loaders is to press Pause/Cancel twice and then Power; on top-loaders, press Start/Pause once to clear and again to restart. If the code stays, or comes back, the washer needs service.

Code list

Top-load washers

LF / Lo FL / F8 E1

Taking too long to fill.

What to do: Open both hot and cold faucets fully; both must be supplied. Check for kinked hoses.

drn

Not draining properly; may be an installation problem.

What to do: Check the drain hose for kinks and the standpipe for clogs.

Ofb

Load out of balance.

What to do: Spread the load evenly around the washplate. Wash bulky items like comforters on the bulky cycle.

OL

Load too large.

What to do: Remove some items and restart.

LdL

Lid will not lock.

What to do: Check for items under the lid and detergent buildup around the lock.

LdU

Lid will not unlock.

What to do: Remove anything sitting on top of the lid, such as a laundry basket.

HC

Hot and cold hoses reversed.

What to do: Shut off water and swap the hoses.

Sud

Too many suds.

What to do: Use only HE detergent, in the right amount.

PF

Power failure interrupted the cycle.

What to do: Restart the cycle.

Front-load washers

F5 E2

Door is not locking.

What to do: Make sure nothing blocks the door and it closes fully. Clear with Pause/Cancel twice and Power. If it persists, the lock needs service.

F7 E1

Motor speed sensing error.

What to do: Make sure shipping bolts were removed and the washer is not overloaded. If it persists, the motor, sensor or control needs service.

F8 E1 / LO FL

Low water flow.

What to do: Confirm both faucets are fully open, hoses are not kinked, and no anti-flood device is restricting flow.

F9 E1

Draining takes longer than expected (about 8 minutes).

What to do: Check the drain hose for kinks and clogs and the standpipe height. Clean the drain pump filter if your model has one.

Sud / Sd

Too many suds.

What to do: Use HE detergent and avoid easy-pour chlorine bleach.

dET

Detergent cartridge not detected (select models).

What to do: Seat the cartridge and close the drawer fully, or ignore if you use single doses.

rL / F34

Items found during the Clean Washer cycle.

What to do: Remove everything and restart Clean Washer.

LOC / LC

Control lock is on.

What to do: Touch (or hold) Control Lock.

Int

Cycle paused or canceled.

What to do: Allow 20 to 30 minutes to drain; unplug for 5 minutes if it stays.

Before you call

What you can safely try

  • Open both water faucets fully and check hoses for kinks.
  • Remove a few items or redistribute the load.
  • Clean the drain pump filter on front-loaders.
  • Use HE detergent in the right amount.
  • For any F-E code, unplug for five minutes and try again.

Turn off power before you touch anything inside the washer. If a step needs tools or panels removed, leave it to a technician.

When to call

When it is time for a technician

  • F5 E2 keeps returning with the door clearly closed.
  • F7 E1 after shipping bolts are confirmed removed.
  • Water stays in the tub after F9 E1 with a clear hose.
  • Burning smell, grinding or loud banging during spin.

A code tells you where to look, not which part failed. We confirm the cause with tests and readings before we quote. Diagnostic from $59, credited toward the repair. Washer repair · Whirlpool repair

Denver note

What we see in the Denver area

Denver's hard water and the habit of using a little extra detergent both lead to suds codes and residue around door locks. Rinse the dispenser drawer and wipe the door seal once a month.

Sources

Where this information comes from

Code meanings are checked against Whirlpool's own published support material and written here in plain language. Models differ, so your owner's manual has the final word.

Pricing

What it costs to get started

One diagnostic fee, credited toward the repair. The full price in writing before any work starts.

Repair prices depend on the part and the labor, so we quote after the diagnosis instead of guessing on the phone. If a repair is not worth it, we will tell you.

How we price repairs · Warranty

Diagnostic visit

from $59

Credited toward the repair

FAQ

Questions we hear

Call (719) 745-8080 with anything not covered here.

What does F8 E1 mean on a Whirlpool washer?

The washer is not getting enough water fast enough. Most often a faucet is partly closed, a hose is kinked or the inlet screens are clogged.

Is F5 E2 expensive to fix?

Often not. It can be something in the way of the door. If the lock itself has failed, a door lock replacement is a common, moderate repair.

Related

Related services and guides

Call now