Skip to content
(719) 745-8080

Error codes · GE

GE Dishwasher Error Codes

GE dishwashers use short codes for drain, fill, temperature and power problems. Many clear with a simple check under the sink. Here is the list and what to do about each one.

  • 14codes explained
  • Checkedagainst GE sources
  • From $59if you need us

How to read GE dishwasher codes

The code appears in the display. GE says disconnecting power for a minute or two can clear a code; if it does not, or it returns, the dishwasher needs service. A number followed by H (like 2H) is just Delay Start, not a fault.

Code list

Drain

C1

Drain took longer than 2 minutes.

What to do: Clean the air gap, check the drain hose and run the disposer to clear it.

C2

Total drain time over 7 minutes.

What to do: Press Reset to stop the beeping, then check the filter and drain path.

C3

Dishwasher will not drain.

What to do: Turn off the breaker for about 30 seconds and reset. If it persists, the pump or drain path needs service.

FTD / F56

Failure to drain.

What to do: Check the drain hose, air gap and disposer; clean the filter.

Fill, float and water

H2O

Low or no water.

What to do: Make sure the hot water valve under the sink is fully on and the hose is not kinked. Level the dishwasher.

C4

Filled twice after a power failure, or the float is stuck, or the sump is clogged.

What to do: Tap the float cover to free it and clear debris from the sump at the back of the tub.

C5

Pump-out time too short.

What to do: Make sure water is on and rerun. Tap the float cover.

LEAK DETECTED / 999 (Floor Protect models)

Possible leak; cycle canceled.

What to do: Turn off water and call for service.

PrS

Pressure sensor signal problem.

What to do: Service needed (sensor or wiring).

Temperature, detergent and power

C6

Incoming water is too cool.

What to do: Run the kitchen tap hot before starting; water should be at least 120°F. Avoid running laundry or showers at the same time.

C7

Water temperature sensor circuit problem.

What to do: Breaker off 30 seconds. If it persists, service.

C8

Detergent cup blocked from opening.

What to do: Move the pan or utensil that blocks it.

PF

Power failure.

What to do: Choose the cycle and press Start.

Cup Open

Detergent cup not closed.

What to do: Add detergent and latch the cup.

Before you call

What you can safely try

  • Clean the filter at the bottom of the tub.
  • Check the air gap and run the disposer.
  • Open the hot water valve under the sink fully.
  • Run the tap hot before starting a cycle.
  • Turn off the breaker for 30 seconds to reset.

Turn off power before you touch anything inside the dishwasher. If a step needs tools or panels removed, leave it to a technician.

When to call

When it is time for a technician

  • C3 or FTD with a clean filter and air gap.
  • LEAK DETECTED or water on the floor.
  • C7 or PrS that returns.
  • Burning smell or tripped breaker.

A code tells you where to look, not which part failed. We confirm the cause with tests and readings before we quote. Diagnostic from $59, credited toward the repair. Dishwasher repair · GE repair

Denver note

What we see in the Denver area

In many Denver homes the water heater sits far from the kitchen, so the first gallon into the dishwasher is cold. That is a common reason for C6 and for poor cleaning. Running the kitchen tap hot for 30 seconds first helps.

Sources

Where this information comes from

Code meanings are checked against GE's own published support material and written here in plain language. Models differ, so your owner's manual has the final word.

Pricing

What it costs to get started

One diagnostic fee, credited toward the repair. The full price in writing before any work starts.

Repair prices depend on the part and the labor, so we quote after the diagnosis instead of guessing on the phone. If a repair is not worth it, we will tell you.

How we price repairs · Warranty

Diagnostic visit

from $59

Credited toward the repair

FAQ

Questions we hear

Call (719) 745-8080 with anything not covered here.

What does C1 mean on a GE dishwasher?

Draining took longer than it should. Usually a clogged filter, air gap or disposer connection.

Is a GE dishwasher worth repairing?

Usually, if it is under about 10 years old and the tub is sound. Pumps, valves and controls are common, practical repairs.

Related

Related services and guides

Call now