Skip to content
(719) 745-8080

Error codes · Hoshizaki

Hoshizaki Ice machine Error Codes

Hoshizaki cubers report faults by beeping and flashing an LED on the control board, not with a text display. The number of beeps tells you which safety tripped. Here is what each one means, based on Hoshizaki service manuals, and what usually causes it.

  • 7codes explained
  • Checkedagainst Hoshizaki sources
  • From $129if you need us

How to read Hoshizaki ice machine codes

Count the beeps in each group; the pattern repeats every few seconds. The 1, 2 and 3 beep alarms shut the machine down and are cleared by pressing the alarm reset button on the control board with the power on. Voltage alarms (6 and 7 beeps) clear themselves when the voltage returns to normal. Exact alarms vary by board and model; this list follows the KM self-contained cuber manual.

Code list

Beep alarms

1 beep

High evaporator temperature (above about 127°F).

What to do: Usually a harvest problem such as a stuck hot gas valve or relay, hot water entering the machine, or a shorted thermistor.

2 beeps

Harvest backup timer: harvest ran over 20 minutes two cycles in a row.

What to do: Open thermistor, hot gas valve not opening, low refrigerant charge, a leaking expansion or water regulating valve, or a weak compressor.

3 beeps

Freeze timer: freeze ran longer than the set limit two cycles in a row.

What to do: Float switch stuck (often scale), a leaking water or hot gas valve, an expansion valve not feeding, low charge or a weak compressor.

6 beeps

Low voltage (around 92 V or less).

What to do: Supply voltage too low; the machine restarts on its own when voltage recovers.

7 beeps

High voltage (around 147 V or more).

What to do: Miswiring or high supply voltage; restarts on its own when voltage is normal.

Newer modular boards

Blinking Power OK LED

Freeze-time correction was triggered.

What to do: Press Alarm Reset with power on. Often points to scale or water flow.

Blinking Ext Harvest LED

Repeated freeze-time corrections within 36 hours.

What to do: Press Alarm Reset; then clean and check water flow and the float switch.

Before you call

What you can safely try

  • Count the beeps and write the number down.
  • Check the water supply valve and filter.
  • Make sure the condenser is clean and air can reach it.
  • Press the alarm reset once with power on.
  • Schedule a cleaning if it has been more than six months.

Turn off power before you touch anything inside the ice machine. If a step needs tools or panels removed, leave it to a technician.

When to call

When it is time for a technician

  • The same alarm returns after a reset.
  • 2 beeps (harvest) or 3 beeps (freeze) more than once.
  • The machine runs but makes no ice.
  • Water leaking from the bin or cabinet.

A code tells you where to look, not which part failed. We confirm the cause with tests and readings before we quote. Diagnostic from $129, credited toward the repair. Ice machine repair · Hoshizaki repair

Denver note

What we see in the Denver area

Denver-area water carries enough minerals to scale a float switch and water distribution parts within months. Most 3-beep calls we run are scale, not a failed part. A cleaning and a water filter change fix many of them.

Sources

Where this information comes from

Code meanings are checked against Hoshizaki's own published support material and written here in plain language. Models differ, so your owner's manual has the final word.

Pricing

What it costs to get started

One diagnostic fee, credited toward the repair. The full price in writing before any work starts.

Repair prices depend on the part and the labor, so we quote after the diagnosis instead of guessing on the phone. If a repair is not worth it, we will tell you.

How we price repairs · Warranty

Commercial diagnostic

from $129

Credited toward the repair

FAQ

Questions we hear

Call (719) 745-8080 with anything not covered here.

How do I reset a beeping Hoshizaki?

Press the alarm reset button on the control board with the power on. If it beeps again after the next cycle or two, the cause is still there.

Why does my Hoshizaki beep 3 times?

The freeze cycle is taking too long. Scale on the float switch is the most common cause in our area, followed by a dirty condenser or water flow problems.

Related

Related services and guides

Call now